WT-5432 FAQs
Buy Now!Corporate SalesFeatured ProductsGive AwayInternational SalesNewsSale ItemsSite MapWar on Spam



 


WT-5432 FAQs 
HomeFeatured ProductsLa Crosse TechnologyProjection Alarm ClocksWT-5432UWT-5432 FAQs

 

 

Atomic Projection Alarm Clock
by

La Crosse Technology

WT-5432

Frequently Asked Questions:

To function properly, the projection alarm clock must be started correctly using high quality alkaline batteries and the time must be set.

 

 

 

Section 1 - Projection Information

 

 

 

    Reason 1

 

Show the projection all of the time

 

 

 

 

 

The projection will be continuously displayed if it is plugged in with the AC adapter. If there is still no projection, put your hand about 2'' from the projection lens. You should see a red dot. If you do not see a red dot, press the button that looks like a sun twice then try it again. The projection will show on the wall or ceiling only when the room is rather dark.

 

 

 

    Reason 2

 

The projection on the wall is upside down

 

 

 

 

 

You can rotate the projection ninety degrees every time you press and release the button that has 4 arrows on it.

 

 

 

Section 2 - Time and alarm information

 

 

 

    Reason 1

 

Time is incorrect or not displaying

 

 

 

 

 

  1. If you have not yet installed the batteries or plugged in the clock and it shows a time, remove the scratch-guard from the LCD panel.
  2. This clock receives a signal from Ft. Collins, Colorado (WWVB) to set the clock to atomic time. Sometimes, due to adverse weather or atmospheric conditions you will not be able to receive a signal immediately. The best way to get a signal is to put your clock in a window facing Colorado until you see the tower icon appear.
  3. If your time is off by an increment of 1 hour, change your time zone to match your location. When a time zone within the continental United States is selected, the clock will display a picture of the US. The selected time zone will be highlighted.

 

 

 

    Reason 2

 

Hour is incorrect (minute and date are correct)

 

 

 

 

 

Be sure time zone and Daylight Saving Time (DST) are selected.

 

 

 

    Reason 3

 

Set the alarm

 

 

 

 

 

Press and hold the corresponding ALM button until the alarm time is displayed. The time should be flashing. Press the ALM1 button to advance the hour and ALM2 button to advance the minute.

 

 

 

    Reason 4

 

Turn off the alarms

 

 

 

 

 

If you look in the upper right-hand corner you should see an alarm icon (((1))), (((2))), or both. The alarm icons signify that an alarm is activated. To deactivate the alarms, press and release the corresponding ALM button. To activate the alarm press and release the ALM button again and the icon will reappear.

 

 

 

Section 3 - Display time, date, alarms, and temperature Information

 

 

 

    Reason 1

 

Display shows --.-

 

 

 

 

 

The maximum open-air distance is 80 feet in a straight line although you should take into account distance and resistance. Subtract 25-30 feet for an exterior wall or any obstruction that is similar in width or composition. Subtract 15-20 feet per interior wall or any obstruction that is similar in width or composition. (An obstruction would include anything that is between the line of sight like a roof, walls, floors, ceilings, trees, etc.) Also keep your units away from electronic appliances like TVís, microwaves, computers, refrigerators, and speakers.

You may have trouble maintaining a signal through metal siding, stucco walls, and UV glass. You can get the remote sensor to transmit through these materials, but it will take a little bit of trial and error. Reset the weather station as mentioned above and change the angle that the remote transmits through the siding or glass until an outdoor temperature remains on the display for an extended period of time. Keep in mind that the signal from the remote must travel through some space (3 inches of air minimum) before reaching the metal wall or glass window.

 

 

 

    Reason 2

 

To display the date, temperature, or alarm times

 

 

 

 

 

Press and release the Mode button to select the desired display mode.

 

 

 

    Reason 3

 

Display outdoor temperature

 

 

 

 

 

  1. Bring both units inside and have the units 3-5 feet apart with nothing in-between them.
  2. Remove the batteries from both units and unplug the display from the wall.
  3. Press one of the buttons at least 20 times or until the display is blank to clear all memory.
  4. Put the batteries back into the remote sensor.
  5. Taking care not to press any buttons, plug the display back into the wall with the AC adapter. (This will ensure that no buttons are pressed. When a button is press during initial setup, it severs the connection of the remote and the display causing no outdoor temperature to show on the display.)
  6. Do not press any buttons for at least 10 minutes after installing the batteries. (Let them establish a good connection.)
  7. An outdoor temperature should be showing on your display. You can now put your outdoor sensor back outside and put batteries into the display.

 

 

 

Section 4 - Sensor Information

 

 

 

    Reason

 

Mounting the remote sensor

 

 

 

 

 

In order to get an accurate reading and to prolong the life of your sensor we recommend that you have it in a sheltered area out of the sun and direct rain. Fog and Mist will not affect the sensor, but a soaking in water may. You can mount it outside under an eve of your house or any other suitable place that will keep it out of the sun and rain. Do not wrap the sensor in plastic or seal it in a plastic bag.

If problems persists, please contact us via email at support@lacrossetechnology.com or by phone at
1-888-211-1923

To Buy, Go UP

Up

Buy Now!Corporate SalesFeatured ProductsGive AwayInternational SalesNewsSale ItemsSite MapWar on Spam

Copyright © 1999 - 2011 Depot 2 You. All Rights Reserved.
sales at depot2you.com